Videx Machine Engineering Ltd.

P.O. Box 260, 5623107 Yahud
20, Shabazi Street, 5623107 Yahud
Israel

Hall map

wire 2018 hall map (Hall 15): stand A53

Fairground map

wire 2018 fairground map: Hall 15

Our range of products

Product categories

  • 01  Wire manufacturing and finishing machinery
  • 01.06  Machinery to solve logistical problems
  • 01.06.05  Cutting
  • 01  Wire manufacturing and finishing machinery
  • 01.06  Machinery to solve logistical problems
  • 01.06.06  Straightening

Straightening

  • 01  Wire manufacturing and finishing machinery
  • 01.07  Fastener machinery (bolts, nuts, rivets, nails)
  • 01.07.01  Bending, forming

Bending, forming

  • 01  Wire manufacturing and finishing machinery
  • 01.07  Fastener machinery (bolts, nuts, rivets, nails)
  • 01.07.02  Hot upsetting

Hot upsetting

  • 01  Wire manufacturing and finishing machinery
  • 01.07  Fastener machinery (bolts, nuts, rivets, nails)
  • 01.07.03  Cold upsetting, forging

Cold upsetting, forging

  • 01  Wire manufacturing and finishing machinery
  • 01.07  Fastener machinery (bolts, nuts, rivets, nails)
  • 01.07.10  Rolling (threads)

Rolling (threads)

Our products

Product category: Straightening

VC-M

VC-M features:     

  • Square Cut face with no burrs. The wire is supported all along the cutting operation.
  • Stainless Steel Track requiring No Adjustment when changing wire diameter.
  • Quick-Clamp positive stop assures length repeatability of ±0.1mm (0.004”).
  • Length change in seconds without dismantling parts.  Optional digital length readout.
  • Quick-Change wire diameter using Preset straightener plugs and cut-off tooling.
  • Extended Length range; from 10mm (3/8”) long slugs to any length in one machine. Optional.
  • Practical Cut-Off speeds up to 600 PPM in ø12mm (1/2”) & 250 PPM in ø25mm (1”).  
  • Reciprocating Straightener (Equivalent to Flying Shear) with a combination of stationary and rotating dies to ensure better surface quality and faster change-over time.
  • Two AC speed controllers enable high production rate for any wire diameter & length.
  • Powerful air brakes assure better safety and no short cuts.
  • Maintenance free machine.  No hydraulics, No clutch, No wearing parts.

More Less

Product category: Cutting

VIC; Impact Cutters for long bars

The Videx VIC Impact Cutters are designed to cut medium and hi-tensile bars.  The machines are offered with optional in-line chamfer station.

The VIC are optionally equipped with computer for calculating the number of parts that can be cut from each bar.  The cut-to-length parts are diverted to one side of the machine while the short residual parts are diverted to the back side of the machine and into a short parts bin (not supplied).

A tight length tolerance (about ±0.2mm measured between centers) is achieved due to the fact that the bars hit a positive stop before cutting.  The wire edge is square and accurate, as the wire is supported during cut-off.

The cut-off is activated by a Hydraulic Impact cut-off piston that provides a good cut face even when working on mild steel. 

The run-off guide is reliable and easy to set. No adjustments are needed when changing wire diameters within a diameter range!

The wire slides between stainless steel bars and is supported by a bottom gate that opens when the cut-off takes place.  The positive stop can be located anywhere along the rails with no need to dismantle any parts of the rails.

The cut-to-length bars accumulate in a magazine from where they are transferred to the chamfer machine, where they are chamfered on one or both ends.

More Less

Product category: Bending, forming

VAS-DBH & DBQ

The VAS line of machines are fed from coil.  The machines pull the wire from coil, straighten and cut to length.

After cutting, the parts accumulate in a magazine, from where they will be transferred to the next operation.  The VAS line can perform a variety of operations, that include cold forming operations such as thread rolling, and material removing operations, such as drilling, pointing, etc...

The parts are automatically transferred inside the VAS machine from one station to the other, and the outcome is a finished part, that does not require any additional operations.

More Less

About us

Company details

Videx Machine Engineering was founded in 1973 as a two man company by David Wiesenfeld, who was until that time a plant engineer of a company producing bolts. The first machines Videx made were semi-automatic, magazine feed thread rollers, that were sold in the local market.

In 1975, Videx has exported the first machine. 2 years later, in 1976, Videx made the first fully automatic machines, working directly from coil. A bending station was added in 1980, and the VAS machine became the first one in the world, producing U bolts from wire coils.

Videx has gradually made its name as a world leader in machinery for specials products from wire coils. Today, most machines are built according to the customer‚s requirements and exact specifications, intended for the manufacturing of special parts and meeting the highest quality standards both for automotive and general.

The high performance accuracy and low maintenance costs of Videx machines have attracted customers from all parts of the world. With its expanding program, 95% of Videx machines is sold to all leading manufacturers in the USA, Europe, Japan, Australia, South America and other countries.

Videx is constantly investing in the Research and Development of new techniques, and in improving the reliability and durability of the machines and the processes. A special emphasis is put in the last 3 years, to reduce the change-over time.

Videx employs 50 people including 10 Engineers, which is our greatest pride and advantage, enabling us to meet the most strict customer demands and requirements.

More Less