Capital Star Steel SA

Parque Industrial de Beluluane, Boane District, Lot 32-48, 2195 Matola, Maputo Province
Mozambique
Telephone +258 84 3904554
Fax +258 84 3904554
cscheepers@capitalstarsteel.co.za

Hall map

Tube 2018 hall map (Hall 7): stand B23

Fairground map

Tube 2018 fairground map: Hall 7

Our range of products

Product categories

  • 01  Raw materials, tubes and accessories
  • 01.06  Tubes made from various manufacturing and processing methods (welded, cold and hot drawn, pressed)
  • 01.06.01  Welded steel tubes (also water boiler tubes)

Our products

Product category: Welded steel tubes (also water boiler tubes)

Electric Resistance Welded Pipe

Capital Star Steel SA uses the high frequency induction welding (HFI) process to manufacture pipes ranging in diameter from 219 mm (8 inch) to 610 mm (24 inch), and in various wall thicknesses.

In the ERW HFI manufacturing process, steel coil is mechanically formed into the required pipe diameter, after which a highfrequency electrical current is applied to heat the pipe to fuse the skelp to form a weld. Since no filler material is added, the weld joint becomes a homogeneous part of the completed pipe, thereby ensuring that the required engineering strength and performance specifications are met. See Table 2.

A completely smooth and high quality pipe is ensured via the process of removing the weld beads both internally and externally.

From raw material to finished pipe, the product undergoes the stringent international standard quality testing, thereby guaranteeing you the highest quality:

More Less

Product category: Welded steel tubes (also water boiler tubes)

ERW Pipe Manufacturing Process

The accumulator allows for the steel strip to be continuously fed into the forming section, where the pipes are formed longitudinally using a combination of forming passes and cage technology. This process also incorporates edge forming and is precisely controlled through fine adjustments in the forming cage. Mill set-ups for various diameters, wall thickness and steel grades are recorded in our mill set-up database, thereby ensuring accurate and repetitive quality.

After the forming process, the pipes are welded by high frequency induction (HFI). After welding, the HAZ is seam annealed using medium frequency induction heating and then air cooled. Pipes are then cut to length using a flying cutoff. Pipe lengths between 6 and 18 meters can be produced off the mill. All pipes are then end-faced to prepare pipe-ends for field welding or flanging as required by the customer. All pipes are hydrostatically pressure tested to specification requirements. The weld seams are then again ultrasonically tested by our highly skilled technical staff to ensure no cracks are formed during the pressure test process.

More Less

Product category: Welded steel tubes (also water boiler tubes)

Pipe Coating and Lining process


The external surfaces of pipes have to undergo a comprehensive abrasive cleaning process before any application of coatings can be done. This process consists of external grit blasting, using mechanical impellers.

Grit blasted pipes to SA 2½ are then externally coated. First the pipes are heated by a medium frequency induction process, where after, the pipes enter a spray cabinet where fusion bonded epoxy powder is electro-statically applied to the surface. Pipes then undergo the application of two layers of extruded polymer coatings from two separate consecutive extruders. The first extruder applies a layer of co-polymer adhesive and the second applies a layer of high density polyethylene.

Pipes are then cooled in a quenching bath to ensure that the coating is well cured before handling. The pipe ends are then mechanically brushed to remove the polyethylene coating as required by the specification, to ensure that the coating will not be affected when pipes are joined by butt welding on site.

Capital Star Steel SA, has industry leading technology for the application of protective coatings and linings to steel pipes. The following protective coatings are on offer;

More Less

About us

Company details

Mozambique Manufacturing Plant
Office: +258 217 30192/3/4
Fax: +258 217 30195

Physical Address:
Parque Industrial de Beluluane
Boane District
Maputo Province
Lot 32 – 48

More Less